Quick Procurement & Configuration Matrix

Executive Product Architectural Overview

The Huawei SFP-10G-CU1M is best understood as a purpose-built physical interconnect rather than as a pair of independent pluggable transceivers. Both SFP+ ends are permanently integrated with the one-metre cable assembly, creating a short direct electrical path between two compatible ports. This architecture is attractive inside racks because it reduces the number of individually ordered items associated with a short optical connection. Instead of planning two optical modules, two connector interfaces and a fibre patch lead, the designer can use a single cable assembly where the equipment vendor and platform configuration support it. That simplification can reduce procurement line items, make rack documentation easier to follow and lower the chance of mixing an incorrect transceiver type or fibre grade during installation.

In enterprise networks, short interconnects appear in many places. A top-of-rack switch may need to connect to an adjacent aggregation device, a security appliance may require a short uplink, a storage host may sit only a few rack units away from a switching platform, or a network team may need a compact lab connection while validating a new topology. A one-metre cable provides a disciplined reach for these scenarios. It encourages clean, localized cabling and avoids unnecessary excess cable when endpoints are physically close. The fixed distance also forces the architect to think about actual rack-unit positions, bend limits and service loops before purchasing, which is important in densely populated cabinets.

The passive electrical design is operationally significant. The assembly does not require an external power adapter, and the cable itself does not introduce a separately managed active conversion element. This supports a straightforward deployment model: verify compatibility, seat each SFP+ end correctly, respect the mechanical routing limits and validate the link at both endpoints. Passive direct-attach cabling is therefore often considered for short reach situations where simplicity is valuable. That simplicity should not be confused with universal interoperability. SFP+ is a standardized physical form factor, but actual acceptance of a direct-attach cable can depend on switch family, port mode, supported accessory lists, software release and vendor policy. Enterprise buyers should therefore treat model validation as part of the procurement process rather than assuming that every device with an SFP+ cage will accept every cable.

Huawei publishes several physical parameters that matter during rack planning. The SFP-10G-CU1M is specified at 1 metre, equivalent to 3.28 feet. Both Connector X1 and Connector X2 are SFP+. The cable is passive and intended for indoor use. The published bend radius is 25 mm, while the minimum clearance for cable routing is 60 mm. These values should be taken into account when a port is close to a rack door, vertical cable manager, patching field or another device faceplate. A cable can be electrically correct yet mechanically unsuitable if the rack geometry forces an excessively tight turn or places stress on the connector.

For UAE infrastructure projects, these details matter because enterprise deployments often involve mixed environments: existing switches, newly supplied hardware, structured cabling, firewalls, servers and management systems may come from different procurement phases. FourTeck can support the buyer by translating the requested cable into a deployment-specific bill of materials. The most useful inputs are the exact equipment models on each end, the interface names, the number of required links, rack layout, delivery location and requested project date. This information allows the quotation to be tied to the intended use rather than treating the cable as an isolated commodity.

Architecturally, the SFP-10G-CU1M fits most naturally where its fixed one-metre reach is an advantage. If a design crosses racks, rows, rooms or floors, an optical solution may provide more appropriate distance and pathway flexibility. If a design needs only a very short same-rack jumper, the direct-attach cable can help reduce component count and preserve a compact topology. The correct decision therefore comes from the physical architecture as much as from the logical network diagram. FourTeck recommends evaluating endpoint support, route length, bend requirements, redundancy design and future maintenance access together before finalizing quantity.

Enterprise Business Value & ROI Benefits

Return on investment for a cable should be measured differently from ROI for a server, firewall or application platform. A direct-attach cable does not create business value by itself; it supports value by enabling a required network link with minimal deployment friction. The relevant metrics are therefore procurement simplicity, installation time, spare standardization, rack cleanliness, compatibility risk and the cost of avoiding rework. If a project uses many short in-rack links, consistent accessory selection can have a noticeable effect on staging efficiency. Conversely, if the physical design exceeds one metre or requires cross-rack flexibility, choosing this cable simply because it is compact would be a false economy. Enterprise value comes from fit, not from forcing one cable type into every topology.

Hardware & Technical Architecture Highlights

The SFP-10G-CU1M architecture centers on two integrated SFP+ connector assemblies joined by a fixed copper high-speed cable. Huawei classifies the product as a high-speed cable and describes its electrical attribute as passive. This means the cable is designed to carry the high-speed electrical signaling directly between supported ports rather than converting the link into an optical signal for transmission over fibre. For a one-metre indoor connection, this architecture offers a compact physical implementation that aligns with close-range equipment placement.

At the connector level, both ends share the SFP+ form factor. The fixed terminations help eliminate mismatches that can occur when one end of a link is fitted with a different optic type from the other. However, the connector shape alone is not a compatibility guarantee. Network devices can implement supported-accessory controls, port operating modes or software-specific restrictions. Engineers should confirm that the exact switch, router, server adapter or appliance supports this model or an approved equivalent direct-attach cable before procurement.

Mechanical behavior is another core part of the architecture. Huawei lists a 25 mm bend radius and 60 mm minimum cable-routing clearance. These measurements should influence faceplate-to-door spacing and the position of cable managers. When equipment is installed close to a closed cabinet door, the connector and cable need room to exit the port before turning. A routing path that compresses the cable too sharply can create strain at the termination and make maintenance harder. Good installation practice includes leaving a controlled service loop, supporting cable weight and avoiding pressure from neighboring bundles.

The fixed one-metre length also shapes topology. Unlike structured fibre cabling, which can be patched through panels and extended over longer pathways, a direct-attach assembly is normally used as a device-to-device cable. That makes it ideal for clear point-to-point links but less flexible when rack positions may change later. Infrastructure architects should therefore distinguish stable same-rack connections from pathways that are likely to be rearranged. If future cabinet moves are probable, the ability to repatch structured fibre may have greater long-term value.

Thermal and airflow planning should not be ignored even though the cable itself is passive. Dense SFP+ port areas can sit in front-to-back airflow zones on switches and appliances. Cable bundles that are overly tight or poorly dressed can restrict access to neighboring ports and complicate fan-tray or line-card service. The objective is not only to make the link work on day one, but to preserve maintainability throughout the equipment lifecycle. Proper labeling at both ends, documentation of the destination port and consistent routing are simple practices that improve infrastructure resilience.

Definitive Technical Specifications & Sizing Notes

The most important sizing parameter is not throughput alone; it is physical reach. Measure the planned route from the first port to the second through the actual cable-management path. A direct line between devices can be shorter than the route required to enter a horizontal manager, travel vertically and return to the destination interface. If the practical route approaches the full one-metre length with no service allowance, a different cable length or link technology may be more appropriate. Buyers should also confirm that the 60 mm routing clearance can be respected at both ends and that the cable will not be forced into a tight bend by a cabinet door.

The second sizing question is compatibility. Provide FourTeck with both endpoint models and, where relevant, line-card or adapter information. For mixed-vendor environments, the acceptance policy of each endpoint must be considered. The third question is redundancy. Two devices may require multiple links for aggregation, failover or dual-fabric design, so quantity should reflect the logical topology as well as the number of physical devices. Finally, identify spare requirements separately from live-link quantity so project stock is controlled rather than absorbed into deployment without documentation.

Configuration, Sizing & Deployment Workbench

Workload headroom in the context of this cable means ensuring that the chosen 10 Gigabit connection aligns with the expected traffic pattern and the capability of the connected equipment. The cable itself does not create additional switching capacity, server throughput or storage performance. It merely provides the physical path. If a server or storage workload is expected to exceed one 10 Gigabit link, architects may need link aggregation, multiple interfaces or a different network speed. User count is therefore not a direct cable specification; it is a system design variable derived from applications, oversubscription, traffic peaks and resilience requirements.

Similarly, storage throughput should be examined at system level. A short direct-attach cable can support a suitable physical connection, but end-to-end performance depends on host adapters, switching architecture, protocol overhead, storage controllers and workload behavior. License terms generally belong to the connected platform rather than the cable, so buyers should confirm any feature licenses needed for link aggregation, advanced switching or fabric functionality. Environmental planning should include rack space, airflow, cable managers and access for technicians. This broader workbench prevents the accessory from being evaluated in isolation from the infrastructure it serves.

Industry Use Cases & Workload Scenarios

Across these sectors, the common pattern is short, controlled, indoor connectivity. The cable is not tied to a particular application workload and should not be sold as though it accelerates a database, protects a clinical system or secures a financial transaction on its own. Its value is at the physical interconnection layer. The correct enterprise use case is one where the network architecture needs a supported 10 Gigabit path between nearby devices and where a one-metre passive direct-attach assembly fits the rack geometry and lifecycle plan.

Technical Feature Deep Dive 1: Throughput & Link Performance Architecture

The SFP-10G-CU1M is described by Huawei as an SFP+ 10G high-speed direct-attach cable. Its role is to provide the physical connection between two compatible SFP+ interfaces over a very short distance. In a properly designed link, this allows the connected devices to exchange traffic without the separate optical conversion components used in a fibre connection. From an architecture perspective, that removes two independent optics from the bill of materials and replaces them with one fixed passive assembly.

Network performance should nevertheless be understood end to end. A 10 Gigabit physical interconnect does not guarantee 10 Gigabits of application throughput under every condition. Actual traffic is affected by protocol overhead, packet size, switch fabric capacity, server bus bandwidth, CPU behavior, storage performance, queueing and network design. Engineers should size the entire path and use interface counters or telemetry after deployment to verify that the link behaves as expected. If a connection consistently approaches saturation, capacity planning may call for link aggregation, parallel fabrics or a move to a faster interface standard rather than merely changing the cable.

For short connections, signal integrity is closely related to using the cable within its designed physical environment. The published one-metre length is fixed, and the bend radius should be respected. Crushing, sharp folding or excessive tension can undermine good cabling practice even when the cable initially establishes a link. Treating cable routing as part of performance engineering helps avoid intermittent faults that are difficult to reproduce. A correctly routed direct-attach cable should be installed so that the connector seats are not carrying the weight of a large cable bundle.

The cable can also simplify troubleshooting because there are fewer discrete components between endpoints than in a link built from separate optics and fibre. When diagnosing a problem, technicians can verify administrative state, link status, interface counters and cable seating, then substitute a known-good approved cable if necessary. This does not eliminate the need for systematic troubleshooting, but the reduced component chain can help narrow the fault domain. For critical systems, keeping documented spare cables is a practical way to accelerate physical-layer substitution during maintenance.

Workload suitability therefore depends on where the link sits in the architecture. A management network, storage path, server uplink or switch interconnect can all have different availability and capacity targets. The cable should be selected only after the logical design confirms that a 10 Gigabit SFP+ physical connection is appropriate. FourTeck can assist with procurement validation, while final performance engineering remains tied to the specific network and application environment.

Technical Feature Deep Dive 2: Resilience, Mechanical Reliability & System Continuity

Resilience begins with acknowledging that any single cable is a component in a larger failure domain. A direct-attach cable can provide a clean short connection, but high-availability design comes from duplicated paths, separate devices, independent power sources and appropriate network protocols. Where uptime is critical, the architect should determine whether each endpoint needs dual links, whether those links should terminate on separate switches, and how traffic will fail over if one path is lost. Ordering quantity should follow that resilience model.

Mechanical reliability is equally important. Huawei’s listed 25 mm bend radius and 60 mm minimum routing clearance are not cosmetic values. They help installers plan how the cable exits the SFP+ cage and travels through cable management. A dense cabinet can tempt technicians to fold a short cable sharply to close a door or route it around another bundle. That practice can add stress at the connector and complicate later maintenance. Designing sufficient front or rear clearance supports a cleaner physical layer and reduces the likelihood that routine service on neighboring equipment disturbs the link.

Labeling supports continuity by making the path understandable to people who did not perform the original installation. Each end should identify the peer device and port in a way that matches site documentation. If the cable is disconnected during a change, the technician can restore the path without relying on memory. For multi-rack projects, consistent color tags or rack labels can distinguish production, management, storage or inter-switch connections, provided the scheme is documented and does not conflict with existing standards.

Spare strategy should balance operational risk with inventory discipline. A one-metre passive cable is compact and easy to store, but stocking uncontrolled quantities across multiple sites can create version ambiguity and waste. Organizations can define a small approved spare pool per data room or project and record part number 02310MUN in the asset or consumables register. When a spare is used, replenishment can be triggered through the same procurement channel. This approach makes recovery faster without turning the storeroom into an untracked collection of cables.

System continuity also depends on testing after installation. Technicians should verify link status at both ends, check for interface errors, confirm the negotiated or configured operating mode and run appropriate traffic validation. In redundant designs, failover should be tested according to the change plan so the organization knows that the second path actually carries service. Physical installation is complete only when the network behaves correctly within the intended topology.

Technical Feature Deep Dive 3: Management, Telemetry & Infrastructure Integration

A passive cable does not act as an independent managed network device, so operational visibility comes primarily from the connected endpoints. Switches, network adapters and appliances expose link state, error counters, utilization, alarms and port configuration through their own management systems. Infrastructure teams should incorporate the cable-supported link into the same monitoring framework used for other interfaces. This provides a historical record of traffic behavior and can reveal increasing errors, unexpected flaps or capacity pressure.

The management value of the cable therefore lies in predictable physical mapping. If the cable is labeled and the endpoints are documented, an alarm on a specific interface can be associated with a known peer and physical route. Network management tools can show the logical condition, while rack documentation tells the technician exactly which cable to inspect. This combination shortens the path from telemetry to physical action. In poorly documented racks, the same alarm can turn into a time-consuming tracing exercise.

Integration with automation platforms follows a similar principle. Configuration management systems may provision switch ports, interface descriptions and link aggregation groups, but the physical cable still has to match the automated intent. Teams can strengthen the relationship by placing peer device names and circuit identifiers in interface descriptions that correspond to the physical labels. During audits, the logical configuration can then be compared with the actual rack layout. This is especially valuable in enterprise environments that use infrastructure-as-code or standardized deployment templates.

For capacity management, interface telemetry should be reviewed over representative business periods rather than during a short installation test. Peak utilization, discards, errors and link transitions can identify whether the 10 Gigabit path remains suitable as workloads grow. If the cable is used in a server or storage design, application and host metrics should be compared with network counters so the team does not attribute every performance issue to the physical link. Good observability is about correlation across layers.

Change management completes the integration story. When equipment is moved, upgraded or replaced, the SFP-10G-CU1M should be revalidated against the new endpoint rather than automatically carried forward. A cable that was supported on the old switch may not be the preferred accessory for a different platform. Updating the bill of materials and compatibility record at each major change keeps the physical infrastructure aligned with the current network design.

What Buyers Should Check Before Purchase

Most purchasing mistakes with direct-attach cables are avoidable. The risks are usually not hidden technical mysteries; they come from ordering the wrong length, assuming universal compatibility, overlooking rack clearance or failing to count redundant links. Use the four checks below before releasing a purchase order.

Buyers should also check the long-term network plan. If a cabinet is due to be reorganized, a one-metre cable that fits today may not reach after equipment moves. If the connection is expected to migrate to a higher interface speed, purchasing a large spare pool could create stranded inventory. Conversely, for standardized racks with stable hardware, keeping a controlled spare quantity can reduce service delay. The goal is to align procurement with the lifecycle of the infrastructure rather than treat cabling as an afterthought.

UAE Regional Availability & Service Ecosystem

FourTeck supports UAE organizations that need enterprise networking accessories with project-oriented quotation and delivery coordination. For SFP-10G-CU1M requests, the most useful procurement workflow is to submit quantity, endpoint models, delivery location and required date together. This allows the inquiry to be treated as a deployment requirement rather than a generic cable request. Current availability, commercial terms and warranty conditions should be confirmed in the formal quotation because they can vary over time.

K1. Dubai Supply & Logistics Support

Dubai buyers can request supply coordination for corporate offices, data centres, system integrators, hospitality groups, free-zone operations and project sites. FourTeck can help organize model validation and quotation handling before delivery. For large rollouts, buyers should provide rack or site quantities so shipments can be grouped logically. Free Zone and special delivery requirements should be disclosed during the inquiry so documentation and access arrangements can be addressed within the project plan.

K2. Abu Dhabi & Al Ain Logistics Reach

Enterprises in Abu Dhabi and Al Ain can request sourcing support for government, industrial, energy, education and corporate environments. A structured inquiry should include the device platforms receiving the cable, quantity per site and target installation date. Where projects involve controlled sites or staged acceptance, delivery sequencing can be discussed as part of the quotation process. Compatibility confirmation remains important because the accessory is used within the context of specific network hardware.

K3. Sharjah & Northern Emirates Logistics Infrastructure

Sharjah and Northern Emirates customers can coordinate enterprise accessory procurement for offices, industrial facilities, educational campuses and branch networks. Project teams should identify whether links are same-rack, adjacent-rack or part of a larger structured cabling plan. The one-metre SFP-10G-CU1M is specifically suited to short reach, so early topology information helps distinguish appropriate direct-attach connections from links that need a different cable length or optical architecture.

K4. Ajman & Surrounding Emirates Logistics Coverage

Ajman buyers can request availability verification, delivery coordination and technical pre-sales guidance for SFP+ direct-attach requirements. Small orders should still include exact endpoint information, while larger projects benefit from a simple connection schedule showing source device, destination device and quantity. This improves consistency during installation and supports clearer handover documentation after deployment.

GCC & Pan-African Supply Chain Reach

FourTeck can support regional technology procurement inquiries where Dubai serves as a sourcing or logistics hub. Export projects may require customs documentation, destination-specific commercial paperwork, freight coordination and accurate part-number control. Buyers should provide destination country, consignee requirements, quantity, project timeline and any special shipping instructions. Freight, duties, taxes, warranty process and delivery commitments should be confirmed on the applicable quotation rather than assumed from UAE domestic supply terms.

L1. Saudi Arabia (KSA) Export & Supply Support

Saudi enterprise and integration projects can submit SFP-10G-CU1M requirements with endpoint details and quantities for regional inquiry routing and commercial review. Project schedules should allow for cross-border logistics and customer documentation. For multi-site deployments, a site-level breakdown supports more controlled staging and delivery planning.

L2. Qatar Market Supply Reach

Qatar buyers can request sourcing and project quotation for validated Huawei networking accessories. Cross-border coordination should include delivery city, consignee information and required installation date. If the cable is being ordered for an existing switch estate, providing the exact switch models helps the pre-sales team identify compatibility questions before shipping.

L3. Oman Regional Distribution Support

Organizations in Oman can request procurement guidance for short-reach SFP+ interconnects and related networking accessories. A complete inquiry should state whether the deployment is a new build, expansion or spare requirement. This context helps distinguish immediate operational replacement needs from planned project quantities.

L4. Kuwait Supply Chain Coverage

Kuwait project teams can coordinate quote requests and export supply through FourTeck’s regional channel. For local information and commercial routing, visit FourTeck Kuwait. Include model SFP-10G-CU1M, part 02310MUN and the destination details in the inquiry to reduce ambiguity.

L5. Kenya & East Africa Supply Infrastructure

Kenyan system integrators and enterprise buyers can request regional distribution assistance, technical inquiry routing and delivery coordination. Visit FourTeck Kenya for localized routing. Export orders should include quantities by project phase and any required shipping or customs documentation.

L6. Uganda Regional Procurement Support

Uganda customers can use FourTeck Uganda for localized inquiry response and project supply coordination. When accessories form part of a broader switch deployment, sending the complete hardware list allows the cable request to be reviewed in its proper architecture context.

L7. Pan-African Regional Logistics & Trade Reach

For broader African projects, FourTeck Africa and FourTeck Global can support inquiry routing for multi-country technology supply. Complex deployments should identify destination markets, site quantities, acceptance requirements and schedule constraints early so the commercial and logistics plan can be built around real project conditions.

Related FourTeck Products & Compatible Alternatives

The correct alternative is determined by distance, endpoint support and cabling architecture. A longer direct-attach cable is not automatically better because excess cable can be difficult to manage in a small cabinet. An active optical cable can offer a different physical approach but must still be validated against both devices. Separate optical modules and fibre provide more flexibility for structured pathways and longer distances, but they also introduce additional components that must be specified correctly. FourTeck can quote a broader link solution when buyers provide the source device, destination device, path length and installation environment.

When comparing alternatives, also consider lifecycle behavior. Fixed direct-attach assemblies are simple for known short links, while modular optics make it easier to change patch lengths without replacing both transceiver ends. If racks are frequently reconfigured, modularity may outweigh the simplicity of a one-piece cable. For stable standardized racks, the opposite may be true. Procurement decisions should follow the expected operating model, not only the initial purchase list.

Why Enterprises Choose FourTeck

Enterprise buyers need more than a part number. A cable can be inexpensive compared with a switch or server, yet the wrong accessory can delay an installation window, force an emergency replacement purchase or create uncertainty during commissioning. FourTeck’s procurement approach is designed around validating the requested model against the project context, preparing a commercial quotation, coordinating delivery and supporting post-sale warranty routing according to the agreed terms.

For the SFP-10G-CU1M, buyers can improve the quality of the transaction by sending the exact endpoint devices, quantity, delivery location and required date with the initial inquiry. This allows the pre-sales conversation to focus on fit rather than simply confirming that a cable exists. When a project includes multiple racks or sites, FourTeck can work from a structured bill of materials so quantities remain clear during quotation and delivery coordination.

FourTeck also supports regional sourcing conversations for GCC and African projects, which can be useful for integrators managing deployments across more than one market. Commercial commitments, lead times, warranty handling and export arrangements remain project dependent and should be captured in the formal quote. This evidence-led approach avoids inflated claims and gives procurement teams a clearer basis for internal approval.

Frequently Asked Questions

1. What is the Huawei SFP-10G-CU1M?

The Huawei SFP-10G-CU1M, part number 02310MUN, is a one-metre SFP+ to SFP+ high-speed direct-attach cable for indoor use. Huawei specifies it as a passive electrical cable assembly. It is intended for short device-to-device connections where both endpoints support the cable and the planned 10 Gigabit interface mode.

2. Is the SFP-10G-CU1M an optical fibre cable?

No. It is a direct-attach high-speed cable with SFP+ connectors integrated at both ends and a passive electrical design. It differs from a connection built with separate optical transceivers and a fibre patch cord. For longer routes or structured fibre pathways, an optical solution may be more appropriate.

3. What is the exact cable length?

Huawei specifies the cable at 1 metre, equivalent to 3.28 feet. Buyers should measure the actual managed cable route rather than the straight-line distance between devices. The route should include movement through cable managers and sufficient service allowance while respecting the cable’s mechanical limits.

4. What bend radius and routing clearance should installers allow?

Huawei lists a 25 mm bend radius and 60 mm minimum clearance for cable routing. Rack planners should make sure the cable can exit each SFP+ port without being forced into an excessively tight turn. Cabinet doors, adjacent connectors and cable managers should not place pressure on the assembly.

5. Will this cable work in every SFP+ port?

Do not assume universal compatibility from the connector shape alone. Support can depend on the equipment family, interface design, software release and vendor accessory policy. Before ordering, provide FourTeck with the exact source and destination device models so the intended combination can be reviewed against available platform information.

6. Does the cable need a separate power supply?

No separate external power supply is specified for the cable assembly. Huawei lists its electrical attribute as passive. The connected switch, server adapter or appliance still requires its normal operating power, and the overall system power design remains the responsibility of the infrastructure architecture.

7. Is the SFP-10G-CU1M suitable for outdoor deployment?

Huawei describes the cable for indoor use. Outdoor or exposed pathways require products specifically selected for environmental conditions, physical protection and applicable site standards. If the planned route leaves a protected indoor equipment environment, provide the details so an alternative interconnect can be considered.

8. Can FourTeck supply the cable in Dubai and elsewhere in the UAE?

FourTeck can handle quotation and delivery coordination for Dubai and other UAE locations subject to current commercial availability and project terms. Send the model, part number, required quantity, delivery destination and deployment date. For better compatibility guidance, include the equipment models at both ends of the planned link.

9. When should I choose a longer DAC or optical cable instead?

Choose an alternative when the real managed route exceeds one metre, when the rack geometry makes the fixed cable impractical, when the connected devices require a different approved accessory, or when the design needs structured cabling and greater distance. Longer DAC, active optical cable and separate optical transceiver options each serve different physical architectures.

10. What information should I send for a quotation?

Provide Huawei SFP-10G-CU1M / 02310MUN, quantity, source device model, destination device model, delivery location, project timeframe and any spare requirement. For multi-site or export projects, include quantities by site and relevant consignee details. This information helps FourTeck prepare a clearer project quotation and identify fit issues early.

Request a Huawei SFP-10G-CU1M Quote for Dubai or UAE

For a procurement-ready quotation, send FourTeck the model and part number, required quantity, equipment models on both ends, delivery location and deployment timeframe. If the project includes redundant links, lab spares or multiple sites, list those quantities separately. FourTeck can then coordinate the commercial response around the actual deployment requirement instead of treating the inquiry as an isolated cable request.

Contact FourTeck for a Project Quote